Disclosure: I may earn a commission if you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Official software should be confirmed on the maker's site. Gear links may also point to StageStock. Full disclosure
Genre build
Metal
Tight, down-tuned rhythm guitars, an aggressive but controlled drum kit, a centered vocal, and a loud, mid-forward master that still leaves the kick and pick attacks intact.
Tempo tendencies: Often 70–90 BPM for half-time heaviness, 120–180+ for thrash and double-time sections. Many modern mixes are written in 4/4 with occasional meter jumps. Keys & harmony: E, D, C, and drop tunings are common. Harmony is often modal or power-chord based; don't over-sweeten the third of the chord if you want weight.
Instruments & sounds
- Two or more tight rhythm-guitar takes, hard-panned, from a high-gain amp or a modern impulse-response cab sim. Leave a mid scoop on the cabs, not a total hole.
- A bass that is more than a sub: a pick or slightly overdriven DI blended with an amp sim, locked to the kick.
- Drums with a short, dry close-mic sound and a controlled room. Sample reinforcement is common on kick and snare; keep some of the real kit so it doesn't turn into a drum machine unless that's the point.
- Leads and layers should be fewer than you think. One mid-forward solo tone, maybe a wide harmony, then get out of the way.
- Vocals: a close, dry lead with doubles on hooks, and screams or gang vocals as their own bus — not the same chain as the lead.
Arrangement
- Write the rhythm arrangement so the kick, bass and palm mutes leave space for each other. If all three play the same subdivision in the same octave, the mix will feel small.
- Use drops: drop the rhythm guitars out for a vocal or a bass figure, then bring the wall back in.
- Keep intros short unless the riff is the hook. Metal listeners will forgive a long fade even less than pop listeners.
EQ
- High-pass guitars until the mud sits with the bass (often somewhere in the 80–120 Hz region — listen, don't copy a number blindly).
- Give the kick a click (typically 3–6 kHz) and a weight region that the bass isn't already filling.
- Snare: a body around the low mids and a crack up top. Cut the boxy band if the close mic honks.
- Carve a vocal pocket in the guitars (often a dip somewhere between 1–3 kHz) rather than only boosting the vocal.
Compression
- Tight bus compression on drums, not a smear. Parallel compression can add size without flattening transients on the main bus.
- Rhythm guitars often need less compressor than you think if the performance is even; a clipper or limiter on the guitar bus can control chugs.
- Vocals: a stable, fast-enough compressor so verses don't disappear under the wall, plus a limiter for screams.
Saturation & tone
- Amp saturation belongs on the guitars and maybe the bass DI, not on everything.
- A little tape or transformer color on the mix bus can glue the wall; too much and the cymbals get harsh and the kick loses punch.
Reverb & delay
- Keep the rhythm section relatively dry. Short rooms or plates on snare, a longer hall or plate on the lead vocal and solo, gated or short rooms if you want a more vintage metal picture.
- Don't bathe tight palm mutes in long halls — they turn to slush.
Bus processing
- Separate buses: drums, bass, rhythm guitars, leads, vocals, effects. Control the wall with the guitar bus, not eight individual faders at the end.
- A mix-bus EQ and a gentle compressor or clipper are common. Leave headroom for the master.
Mastering targets
- Metal masters are often louder than a typical streaming-friendly pop master, but a smashed limiter that eats transients will make a heavy song feel small. Aim for impact first.
- A common streaming starting point is around -14 LUFS integrated with true-peak headroom of -1.0 dBTP or more, but many metal releases are louder. Check the platform and leave the transients intact. Don't chase a number that wrecks the kick.
- Check the mix on small speakers: if the riff disappears, it wasn't a loudness problem.
How-to notes by DAW
- Ableton Live 12: Use drum racks or a multi-out drum sampler for click vs body on the kick. Group rhythm guitars and follow with a utility gain and a clipper. Session View is useful for arranging heavy/drop sections as scenes.
- Logic Pro: Track Stacks for the guitar wall and drum kit, plus stock Amp Designer or a third-party IR loader. Use Quick Swipe comping on vocals and tight guitar takes.
- Pro Tools: Clip gain the quiet mutes before the compressor. Route the guitar wall to a bus with a clipper. This is a bread-and-butter Pro Tools session shape.
- REAPER: Take advantage of routing: a DI track feeding multiple cab sims, and a dry/wet folder for parallel drum compression, without a pile of duplicate tracks.
- FL Studio: Producer Edition or higher for the vocals. Use the mixer with a dedicated guitar bus and Maximus or a limiter for the wall; don't crush the drum bus the same way.
Written for Breakin' the DAW, November 20, 2026.